SHARE

Single-Engine Komatsu PC2000 Crawler Excavator Packs More Power

By Larry Stewart, Executive Editor | September 28, 2010

 Komatsu PC2000LC-8 crawler excavator
The 445,000-pound Komatsu PC2000LC-8 crawler excavator, swinging a 15.7-cubic-yard bucket 30 to 40 degrees, clocks 25-second loading cycles. It is sized to load a 100-ton truck in four passes.

At the opening ceremonies of its new training center in Cartersville, Ga., Komatsu announced that it replaced the twin-engine PC1800 excavator/shovel with the single-engine PC2000LC-8, adding nearly 50 horsepower (a 5.5-percent gain). The first of these 445,000-pound excavators was on hand in the Cartersville demo area for trade journalists and Komatsu dealers to see how the single engine simplified the mining machine.

The PC2000 steps into the operating-weight gap between Hitachi's EX1900-5 BE and EX2500-5 BE. While the PC2000's dig depth is an impressive 3½ feet deeper than the EX1900, it's not deeper than the PC1800 that it replaced. Standard bucket size and engine horsepower remain about the same, if a little less than the smaller Hitachi's. Komatsu's Tier 2 power solution is its SAA12V140E-3 diesel, rated at 956 net horsepower.

Reducing the population of hydraulic pumps aboard the mountainous earthmover was a natural outgrowth of the single-engine design. Four much-larger pumps — a pair of twins — replace the PC1800's 10 hydraulic pumps, reducing power lost to heat and bringing about dramatic hydraulic-system simplification. For example, Komatsu did away with the dedicated swing pump, and the PC1800's dual drives in each track are replaced by single hydraulic motors.

The engine, hydraulic pumps, and cooling system (with enlarged oil cooler) are packed in a power module that can be lifted off the machine in one 22-ton load. The simplified power train also reduces required maintenance hours and the overall number of parts, which Komatsu says contributes to total cost reduction.

Boom-cylinder bore increased about 4 inches (from 280 mm to 300 mm) for faster cycle times. Paul Dawlearn, product manager for loading equipment with Komatsu mining, says that the unit, when swinging 30 to 40 degrees loading with a 15.7-cubic-yard bucket, clocks 25-second cycles. The PC2000LC-8 is designed to load a 100-ton truck in four to five passes.

A new, pressurized cab designed only for use in mining shovels is 30 percent larger than the predecessor's cab and cooled by a twin air conditioner. New damper mounts, in conjunction with power module packaging, attain car-like noise levels of 64.5 dB(A). Indeed, I had to turn down the air-handling fan in order to confirm that the engine had started when cranking the ignition, and had to listen closely to detect a sound difference when the engine revved to high idle. A new, 7-inch LCD monitor provides improved panel visibility to ensure a secure and smooth operation.

Suggested retail price on the Komatsu PC2000LC-8 is expected to be about $2.1 million.

Competitive Crawler Excavator/Shovels
Bucket Cap. (cu.yd.) Net HP Lift Cap. (lbs.)* Max. Dig Depth Arm Length Oper. Weight (tonnes)
* Over the end at 30-ft. radius, ground level. Source: Spec-Check.com
Hitachi EX1900-5 BE 15.7 966 88,000 26′ 10″ 11′ 10″ 186.5
Komatsu PC1800-6 15.7 908 n/a 30′ 5″ 12′ 10″ 180
Komatsu PC2000LC-8 15.7 956 103,900 30′ 4″ 12′ 10″ 200
Hitachi EX2500-5 BE 19.6 1,302 186,000 28′ 1″ 13′ 9″ 239
Komatsu PC3000 19.5 1,260 n/a 25′ 7″ 13′ 1.5″ 253
Liebherr R994 Li 17 1,142 n/a 28′ 6″ 13′ 1.5″ 229


Get free price quotes from multiple sellers with BuyerZone

Are you looking for a full size or mini excavator?
Are you looking for a full size or mini excavator?
How many excavators are you interested in?
How many excavators are you interested in?
Do you prefer a new or reconditioned excavator?
Do you prefer a new or reconditioned excavator?
How soon do you plan to purchase the excavator?
How soon do you plan to purchase the excavator?
Approximately what operating weight do you need?
Approximately what operating weight do you need?
What will you use the excavator for?
What will you use the excavator for?
How do you prefer to finance your excavator?
How do you prefer to finance your excavator?
What is your zip code?
What is your zip code?
What is your email address?
Please describe any special features or additional needs for your excavator, such as specific performance criteria, attachments, etc.
Let's finish up! Who do we have the pleasure of working with on this quote request?
Please provide your role and company information.
Last question. Where is your business located?
Company Address

Your privacy is important to us. By submitting this form, you consent to BuyerZone and up to six companies calling you at the phone number provided using automated phone technology. Consent is not a condition of purchasing any products or services.

expand_less