Electronic Fuel Injection Redefines Wheel Loaders

Sept. 28, 2010

 

The Komatsu hydrostatic drive uses a high-speed and low-speed motor. When lots of torque is needed, both drives work through the crankcase; but when the machine gets up to speed, a clutch removes the low-speed motor from the driveline. Liebherr and Terex loaders have simlar drives.
Komatsu's new 100- to 200- hp loaders come with hydrostatic transmissions. A loaded WA250-5 climbed hills 6 percent faster than its predecessor in Construction Equipment Field Tests, and loaded trucks faster at a minimum 29 percent fuel-economy advantage.
Volvo's front-end linkage has a strut connecting the top of the Z bar to the bucket, actuated by hydraulic cylinders attached to the bottom of the Z bar (below the boom arms). Link-Belt and the smaller hydrostatic machines from Terex have similar configurations. The design is said to deliver high breakout forces through the lift arc as well as level-lifting capability.
Coolers arranged in a cube around the fan prevent any stacking of the heat exchangers, eliminating some places where debris can get trapped in the Case and New Holland cooling module.
The Universal Upgrades

 

These important improvements have become nearly universal on the newest generation of wheel loaders:

Emissions-compliant engines - With electronic fuel-injection controls, turbochargers and aftercoolers

Single-joystick controls - For loader hydraulics. Two-lever control is sometimes an option

Limited-slip differentials - Some offer torque-proportioning differentials

Improved cabs - More glass, better heating and air conditioning, and often a better seat

Easier maintenance - Grouped grease fittings, fluid drains and filters can be serviced from ground level

Tables:
  • Average Wheel Loader Costs
  • 3-Cubic-Yard Competitors
Buying File Gallery:
  • Komatsu
  • Link-Belt
  • Case
  • Liebherr
  • Daewoo
  • New Holland Construction
  • John Deere
  • Caterpillar
  • Volvo
  • Hyundai
  • Kawasaki
  • Dressta
  • JCB
  • Terex
  • Coyote

Category creep has characterized the 100- to 200-hp range of loaders for a long time. The latest round of redesigns continues the trend to higher horse-powers, heavier machines and bigger buckets, but the new emissions-compliant engines have exaggerated the usual productivity gains even while slashing fuel consumption.

Technology leaders among wheel-loader manufacturers have leveraged the benefits of electronic fuel injection¡ªa feature required to meet EPA's Tier II exhaust limits¡ªto upgrade transmissions, hydraulic systems and cooling systems. Some who are particularly motivated to take market share have also been angling for advantages with hydrostatic transmissions and changes in loader design.

Productivity has changed a lot in one generation. Consider Caterpillar's 928. The F Model was rated at 120 horsepower. With its standard 2.4-cubic-yard bucket, it generated 23,874 pounds of breakout force. The 928G comes with 143 horsepower and a 3-cubic-yard bucket. The smallest bucket available on the G, at 2.5 cubic yards, is comparable to the F's standard equipment. With it, the G delivers 16.4 percent more breakout force and weighs just 1,900 pounds more than the F. That kind of metamorphosis has been repeated regularly in this generation of wheel loaders. New models have been hitting the market with improvements in breakout force disproportionate to their increase in horsepower and weight.

It starts with the engine. Engines across this category now come turbocharged, with intercoolers to cool intake air between the turbo and cylinder head. Before the Tier II emissions regs came into effect in January 2003, many wheel loaders under 200 horsepower got by without electronic fuel injection. Meeting the limits made engine computers universal.

Electronic control of fuel systems allows more precise and flexible control of fuel delivery, which increases fuel efficiency and improves horsepower and torque output. Of course, the degree to which different engines deliver each of these benefits varies, but virtually all Tier-II-compliant engines can credibly claim these advantages.

Wheel-loader technology leaders distinguish themselves by how well they integrate electronic fuel injection with controllers on hydraulic systems and transmissions. When the computer controlling fuel injection communicates with computers on the hydraulic system and transmission, each component "knows" how the other components are working. And they can adjust their output to get more out of the machine.

Some manufacturers have exchanged traditional open-center hydraulics for closed-center systems, replacing gear pumps with variable piston pumps like those used in hydraulic excavators. A closed-center hydraulic system relies on a variable-displacement piston pump that can push more or less hydraulic flow into the system in response to changes in system pressure. It improves fuel efficiency because the system isn't constantly pushing oil over relief.

Open-center hydraulics, which are much more common in this wheel-loader category, typically use a fixed-displacement gear pump whose flow only changes in a fixed ratio with engine speed. Excess flow returns to the hydraulic reservoir through a relief valve. Open-center hydraulics tend to use more fuel, but they are simpler and generally less expensive to build and maintain than a closed-center system.

Electronic fuel injection makes closed-center hydraulic systems attractive because the computer controlling the variable piston pump can work together with the engine computer to reach greater levels of power and efficiency. That's why work modes and power-boost options, like those on excavators, are appearing in some wheel loaders.

A more common extension of electronic technology in 100- to 200-hp wheel loaders is the electronically controlled powershift transmission. The transmission's computer senses clutch-engagement pressure, and proportional valves enable precise control of the hydraulic clutches. Clutch pressure is adjusted automatically for smooth shifts in any working conditions. Electronic engine controls have paved the way for highly efficient hydrostatic transmissions, too. Komatsu, Liebherr, Terex and Coyote all offer hydrostatic drives instead of mechanical transmissions. (Two of Terex's five models are hydrostatic.)

Heavy-duty hydrostats employ a powerful hydraulic pump driven by the engine. The pump supplies two hydraulic motors¡ªtypically one high-speed motor and one low-speed motor. When lots of torque is needed, both drives work through a crankcase. When the machine gets up to speed and torque demand falls off, a clutch removes the low-speed motor from the driveline.

Construction Equipment had the opportunity to Field Test hydrostatic performance by comparing Komatsu's new hydrostatic WA250-5 to the WA250-3 with its powershift gearbox. The Dash-5 machine is a little lighter than the Dash 3, but in truck-loading tests, the new unit's faster cycle times and better bucket-fill factors made it nearly 14 percent more productive than the WA250-3. And the Dash 5 delivered a huge 51 percent fuel-economy advantage. In a 150-foot load-and-carry operation, the Dash 5 outproduced the Dash 3 by 5 percent at a 29 percent advantage in fuel economy.

High-tech engines are bringing maintenance benefits to wheel loaders as well. Most manufacturers enlisted the Tier-II engines' electronics to control a hydraulic fan drive. Separating the fan from the engine for the first time has created a variety of solutions to traditional cooling problems.

Most hydraulic fans are reversible. Either automatically or at the push of a button, the fan can be reversed to blow off debris that has collected on the windward side of the coolers. Manufacturers have been rethinking cooling airflow as they've worked to make room for an intercooler among the radiator, air-conditioner condenser, hydraulic-oil cooler, transmission-oil cooler, and fuel cooler. Case and New Holland, John Deere, JCB, Liebherr, and others have isolated the cooling system in a compartment separate from the engine. Coolers are being repositioned so that they are no longer stacked.

Case, New Holland and Liebherr machines mount their cooling unit between the cab and the engine. In the CNH cooling module, the radiator and all the coolers are arranged in a cubic shape around the fan. None are stacked. The fan pulls air through the coolers and blows it over the engine. The design allowed Case to move the engine rearward, behind the rear axle. Improved counterweighting translated into better breakout forces.

Wheel loaders are the most common high-dollar machines selling. The only equipment categories with larger populations in North America are skid-steer loaders and backhoe-loaders, the sales of which don't deliver nearly as much profit as a wheel loader. It's a profit opportunity that has attracted increased brand competition. New competitors such as Liebherr, Link-Belt and Terex have been trying to cut themselves a piece of wheel-loader pie.

As mentioned, Liebherr and Terex are working to distinguish their products with hydrostatic transmissions. Link-Belt and Terex offer a twist on the usual Z-bar front-end linkage that resembles the Volvo arrangement. It's a Z-bar, but reverses the traditional connections. The hydraulic cylinder attaches to the bottom of the bar, and the link to the bucket connects to the top. The makers claim the geometry delivers more breakout force to the machine's full lift height than the common Z-bar. And Link-Belt says that its fork-leveling sensors automatically regulate the position of the lift and curl cylinders to keep the load level through the lifting cycle.

Tier II engines have no doubt consumed much of recent research-and-development resources for 100- to 200-hp loaders. But there is ample variation in hydraulic systems, transmissions, cooling systems, and front-end linkages to make today's wheel-loader offerings more than just an engine competition.

Average Wheel Loader Costs Size range List price Hourly cost* * Monthly ownership cost (based on list price) plus operating expenses, divided by 176 hours. Source: EquipmentWatch.com, phone 800/669-3282 100 to 134 horsepower $107,969 $41 135 to 174 horsepower $144,195 $52 175 to 199 horsepower $202,235 $68 3-Cubic-Yard Competitors Model Bucket Cap. (cu. yd.)* Horsepower Operating Weight (lbs.) Breakout Force (lbs.) Dump Clearance** *This bucket used to establish performance specs **Clearance with bucket dumped at 45-degree angle Link-Belt's L125¡ªat 130 horsepower, and weighing 25,000 pounds¡ªprobably fits the 3-cubic-yard category better than the L130, but LBX doesn't list performance specifications with a bucket bigger than 2.6 cubic yards. Terex appears twice on this chart because the company sells the Schaeff line that it acquired several years ago and the Terex-branded Daewoo machine in the 3-cubic-yard category. Specifications are given for comparison only and are subject to change. Hyundai HL740-7 2.7 133 25,350 26,190 9' 4" Kawasaki 65ZV 2.8 134 23,610 22,530 9' 0" Intensus WL40G 2.9 168 33,069 31,472 9' 6" Case 621D 3.0 135 26,079 23,410 9' 2" Caterpillar 928G 3.0 143 26,094 24,464 9' 4" Dressta 520E 3.0 142 23,270 23,260 8' 11" New Holland LW130.B 3.0 136 25,882 23,397 9' 2" Volvo L70E 3.0 152 28,610 22,250 9' 4" John Deere 544J 3.0 134 27,486 22,672 9' 2" Komatsu WA250-5 3.0 134 24,846 27,205 9' 4" Terex SKL873 SP 3.0 144 29,767 24,425 9' 10" Daewoo Mega 250-V 3.1 158 30,420 29,100 9' 6" JCB 426 ZX 3.1 132 28,600 29,150 9' 5" Terex TXL 250-1 3.1 158 30,420 29,100 9' 6" Link-Belt L130 3.2 166 30,305 27,876 9' 4" Liebherr L 538 3.3 136 27,130 23,600 9' 5"
Web Resources
  Case
www.casece.com
Caterpillar
www.cat.com
Coyote
www.coyoteloaders.com
Daewoo
www.dhiac.com
Dressta
www.dresstanorthamerica.com
Hyundai
www.hceusa.com
Intensus
www.intensus.com
JCB
www.jcbna.com
John Deere
www.deere.com
Kawasaki
www.kawasakiloaders.com
Komatsu
www.komatsuamerica.com
Link Belt
www.lbxco.com
Liebherr
www.liebherr.com
New Holland
www.newhollandconstruction.com
TCM
www.tcmglobal.net
Terex
www.terexamericas.com
Volvo
www.volvoce.com