Equipment Type

Caterpillar C Series ADTs

Cat C Series articulated dump trucks—725C, 730C, and 730C EJ ejector—feature new engines with more power, advanced transmission control, enhanced operator amenities, new serviceability features, and for the 730C and 730C EJ models, automatic traction control.

November 11, 2013

Cat C Series articulated dump trucks—725C, 730C, and 730C EJ ejector—feature new engines with more power, advanced transmission control, enhanced operator amenities, new serviceability features, and for the 730C and 730C EJ models, automatic traction control.

The 725C has a rated payload capacity of 26 tons, and the 730C and 730C EJ models are rated at 31 tons.

The Cat C9.3 ACERT engine powers the 725C and is rated at 314 net horsepower, and the Cat C13 ACERT in the larger models has 367 net horsepower. All three models are available in US EPA Tier 2/E.U. Stage II equivalent, Tier 3/Stage IIIA equivalent, or Tier 4 Final/Stage IV configurations to meet worldwide emissions standards. A DPF and SCR system provide exhaust aftertreatment for Tier 4 Final/Stage IV models.

Compared with predecessor models, the 725C has a 4 percent gain in gross power and a 20 percent boost in gross torque; 730C and 730C EJ models have nearly 16 percent more gross power and more than a 30 percent gross torque improvement.

The Cat 6F/1R power-shift transmission, which electronically modulates clutch engagement pressures for smooth, positive shifts, now also incorporates Caterpillar Advanced Productivity Electronic Control Strategy (APECS). The APECS system improves acceleration, maintains torque converter lock-up (and ground speed) during critical shifts, increases rimpull, provides automatic speed holding, modifies shift points to match operating conditions (for increased fuel economy), and automatically reduces retarding forces on lesser grades in lower gears, Cat says.

For controlling speed on downhill grades, 730C models employ a new engine compression brake that provides 60 percent more retarding power than predecessor models. The 725C uses a fluid retarder with four operating modes. Both systems effectively manage speed and minimize service brake application for extended brake life.

All three new C Series models feature full-time, six-wheel drive and are equipped with wet-disc-clutch locks in the axle differentials and the inter-axle differential. On-the-go application of the locks, which assist traction in adverse conditions, is done at the 725C operator's discretion via in-cab controls, while the new Automatic Traction Control system in the 730C models applies the locks automatically—and proportionally—as ground conditions dictate – with zero input required by the operator.

Caterpillar C Series Specifications

725C

  • Engine: Cat C9.3 ACERT
  • Horsepower: 314
  • Rated payload: 26 tons
  • Heaped capacity: 19.4 cubic yards
  • Total loaded weight: 103,220 pounds
  • Max. fwd. speed: 35 mph

730C/730C EJ

  • Engine: Cat C13 ACERT
  • Horsepower: 367
  • Rated payload: 31 tons
  • Heaped capacity: 23 cubic yards
  • Total loaded weight: 114,860 pounds/121,078 pounds
  • Max. fwd. speed: 34 mph

 

File Attachment

other Caterpillar Inc. products

Cat 730, 730 EJ, and 735 articulated dump trucks have redesigned operator stations.

Cat 730, 730 EJ (Ejector), and 735 articulated dump trucks have redesigned operator stations.

Caterpillar 24 motor grader has a 24-foot-wide moldboard

Caterpillar 24 motor grader has a 24-foot-wide moldboard

More like this

Add comment

Plain text

  • No HTML tags allowed.
  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.
Image CAPTCHA
Enter the characters shown in the image.
Overlay Init